2016 November: Difference between revisions

From EOVSA Wiki
Jump to navigation Jump to search
Line 12: Line 12:
'''01:08 UT''' Set up the schedule to do a long run on 3C84 with the low-frequency receiver, using pcal_lo.fsq (all bands 2.5-6 GHz).  One major change is that the PA can be set, so I set it for -30.  I would predict that the chi-dependence will shift by 30 degrees (the phase jump will occur at a different hour angle), but the non-intersecting axes issue will cause the same symmetric phase rotation (it depends on elevation only).
'''01:08 UT''' Set up the schedule to do a long run on 3C84 with the low-frequency receiver, using pcal_lo.fsq (all bands 2.5-6 GHz).  One major change is that the PA can be set, so I set it for -30.  I would predict that the chi-dependence will shift by 30 degrees (the phase jump will occur at a different hour angle), but the non-intersecting axes issue will cause the same symmetric phase rotation (it depends on elevation only).


'''04:20 UT''' 3C84 schedule begins
'''04:20 UT''' 3C84 schedule begins.


'''12:20 UT''' 3C84 schedule should end.
'''12:00 UT''' 3C84 schedule ends.


= Nov 10 =
= Nov 10 =
'''03:00 UT''' Note, the above observations showed no coherence, for reasons unknown.  The receiver will be checked for pointing and focus using a total power source.  I attempted to observe the Moon at the current time, but it happens to be at -6 Declination, so it is in the geosynchronous satellite belt and could not be peaked up in total power.  I will observe Cyg A when it rises at ~ 21:20 UT today.
'''03:00 UT''' Note, the above observations showed no coherence, for reasons unknown.  The receiver will be checked for pointing and focus using a total power source.  I attempted to observe the Moon at the current time, but it happens to be at -6 Declination, so it is in the geosynchronous satellite belt and could not be peaked up in total power.  I will observe Cyg A when it rises at ~ 21:20 UT today.

Revision as of 17:47, 10 November 2016

Nov 04

19:18 UT Reboot ROACHes to clear fault light and test whether large delays are still present. They were power-cycled and reloaded.

19:24 UT Started roachcal.scd to take packet capture data for checking delays. Still bad!

Nov 05

03:41 UT Found a potential problem in DELAYCAL_END.ctl, so took another two sets of roachcal.scd data. Still bad!

04:14 UT Started roachcal.scd for another set of data. After studying schedule.py, another problem was found. DELAYCAL_END command has to have CIEL-2 as second value on the line, otherwise source id is set to None! Yay! It finally worked!

Nov 09

01:08 UT Set up the schedule to do a long run on 3C84 with the low-frequency receiver, using pcal_lo.fsq (all bands 2.5-6 GHz). One major change is that the PA can be set, so I set it for -30. I would predict that the chi-dependence will shift by 30 degrees (the phase jump will occur at a different hour angle), but the non-intersecting axes issue will cause the same symmetric phase rotation (it depends on elevation only).

04:20 UT 3C84 schedule begins.

12:00 UT 3C84 schedule ends.

Nov 10

03:00 UT Note, the above observations showed no coherence, for reasons unknown. The receiver will be checked for pointing and focus using a total power source. I attempted to observe the Moon at the current time, but it happens to be at -6 Declination, so it is in the geosynchronous satellite belt and could not be peaked up in total power. I will observe Cyg A when it rises at ~ 21:20 UT today.